Sold

Case 570 LXT Skip Loader

Details
Year 2000
Make Case
Model 570 LXT
Type Skip Loader
Hours 3900
Condition Very Good
Description

2000 Case 570 LXT Skip Loader, Case 4-390 Engine, Naturally Aspirated, 4-Cylinders, 2WD - 4WD, 4-1 Bucket included, All Maintenance points serviced, ready to work! 

(NOTE: AVAILABLE ONLY VIA APPOINTMENT. PLEASE GET IN TOUCH AND SCHEDULE AN APPOINTMENT.)

Engine

  • Make: Case
  • Model: 4-390
  • Type: 4-Stroke, Naturally Aspirated
  • Cylinders: 4
  • Fuel Injections: Direct
  • Bore/Stroke: 4.02" x 4.72"
  • Displacement: 239 in3
  • Horsepower: Gross - 75 @ 2200 rpm | Net - 71 @ 2200 rpm
  • Maximum Torque: Gross - 197 lb·ft @ 1400 rpm | Net - 193 lb·ft @ 1400 rpm

Driveline

Fully synchronized 4-speed forward reverse shuttle transmission with hydraulically actuated clutches and clutch disconnect buttons on the transmission shifter and loader control lever. Electronically activated forward/reverse shuttle shift and 4WD engagement with optional mechanical front wheel drive. 4WD activation on-the-go. Maintenance-free, self adjusting, inboard mounted, wet disc brakes are hydraulically actuated.

Travel Speeds

  • Forward: 1st - 3.7 | 2nd - 6.6 | 3rd - 12.8 | 4th - 25.5
  • Reverse: 1st - 3.7 | 2nd - 6.6 | 3rd - 12.8 | 4th - 25.5

Hydraulic System

Front mounted, positive displacement, gear-type tandem. Heavy-duty oil cooler.

Loader Hydraulic Pump Capacity

  • 28.5 gpm @ 2200 rpm @ 3000 psi

Loader Control Valve

2 or 3-spool sectional valve with single lever control for lift, tilt and auxiliary hydraulics. Positive hold “float” and “return-to-dig”.

Loader Valve Main Relief Pressure

  • 3000 + 100 - 0 psi

3 Pt. Hitch Hydraulic Pump Capacity

  • 0 to 8 gpm @ 2200 rpm @ 3000 psi

3 Pt. High Control Valve

  • Sectional, open-center, parallel circuits with variable flow control of 5 sections for lift, pitch, tilt and (2) auxiliary.

2 Pt. Hitch Valve Main Reliefe Pressure

  • 2,000 psi

3 Pt Hitch Secondary Relief Settings

  • Auxiliary "B" Port: 1,000 psi
  • Lift "A" Port: 1,000 psi
  • Lift "B" Port: 1,750 psi

Filtration

  • 7-micron, full flow replaceable cartridge on return line. Condition indicator light

Service Capacities

  • Fuel tank: 31.4 gal
  • Hydraulic reservoir: 13.9 gal
  • Total hydraulic system: 33.0 gal

Transmission

  • 2WD Total system: 19.5 qt
  • 4WD Total system: 22.0 qt

4WD Front axle

  • Differential: 5.8 qt
  • Planetaries (each): 0.74 qt

Rear axle

  • Differential: 15.0 qt
  • Planetaries (each): 1.6 qt
  • Engine oil w/filter: 11.6 qt

Cooling system

  • w/heater: 17.4 qt
  • w/o heater: 16.7 qt

Electrical System

  • Voltage: 12 Volts, negative ground
  • Alternator: 12 Volts, 65 amp
  • Battery: Maintenance-free | 685 cold-cranking amps @ 0°F

Loader Dimensions

  • Overall operating height: 13'8" (General Purpose) | 14'3" (4-In-1)
  • Bucket rollback @ groundline: 40° (General Purpose) | 40° (4-In-1)
  • Dump angle @ full height: 46° (General Purpose) | 45° (4-In-1)

Digging depth below grade

  • Bucket flat: 7.8" (General Purpose) | 7.1" (4-In-1)
  • Clam open (dozing): NA (General Purpose) | 4.4" (4-In-1)

Dump clearance @ full height, 45° dump

  • Bucket: 8'8" (General Purpose) | 8'11" (4-In-1)
  • Clam open: NA (General Purpose) | 9'8" (4-In-1)

Dump reach @ full height, 45° dump

  • Bucket: 25.9" (General Purpose) | 25.3" (4-In-1)
  • Clam open: NA (General Purpose) | 11.8" (4-In-1)

Reach from front axle centerline,

  • Bucket on ground: 75.3" (General Purpose) | 72.7" (4-In-1)
  • Lift capacity to full height: 5,293 lb (General Purpose) | 5,197 (4-In-1)
  • Height to bucket hinge pin raised: 11'2" (General Purpose) | 11'2" (4-In-1)
  • Breakout force (dump cylinders): 7,956 lbf (General Purpose) | 7,879 lbf (4-In-1)
  • Breakout force (lift cylinders) w/box scraper: 7,811 lbf (General Purpose) | 7,116 lbf (4-In-1)
  • Breakout force (lift cylinders) w/out box scraper: 6,375 lbf . (General Purpose) | 6,175 lbf (4-In-1)
  • Bucket cutting edge width: 82" (General Purpose) | 82" (4-In-1)
  • Maximum grading angle: 116° (General Purpose) | 116° (4-In-1)
  • Maximum clam opening: NA (General Purpose) | 38.3" (4-In-1)
  • Moldboard height: NA (General Purpose) | 36.8" (4-In-1)
  • Raising time to full height: 4.5 sec (General Purpose) | 4.4 sec (4-In-1)
  • Bucket dumping time: 0.8 sec (General Purpose) | 0.8 sec (4-In-1)
  • Lowering time, power down: 2.7 sec (General Purpose) | 2.2 sec (4-In-1)
  • Lowering time, return-to-dig: 3.1 sec. (General Purpose) | 2.4 sec (4-In-1)